"DON'T APPLY THE SAME MISTAKE TWICE"
ABOUT
MCU-Coatings NZ is part of the global leading manufacturer of moisture cure polyurea (MCU) marine and protective coatings to protect steel, concrete, aluminium, stainless steel and iron from corrosion. With a history of 30 years, currently, MCU-Coatings is one of the fastest growing moisture cure polyurea (MCU) coating technologies worldwide.
The primary reasons for the success of MCU-Coatings technology is, the ease of application and its proven long-life performance. The coatings performance such as; durability and corrosion resistance, even when applied in less than ideal conditions, is second to none and in a league of it’s own!
EASY APPLICATION & DURABLE
MATERIAL COSTS REDUCED
10 - 30%
FASTEST PROJECT COMPLETION TIME
2 - 3 TIMES BETTER PREFORMANCE
Primers
-
Surface tolerant single component, zinc-rich primer
-
Approved for Class B Slip Coefficient.
-
Versatile, easy to use, corrosion resistant primer.
-
Replaces epoxy zinc. Better performance than inorganic zinc.
-
Unlimited recoat time
-
Overcoatable by itself
-
Tolerates flash rusting
-
High DFT tolerance
-
1 primer for any type of surface prep. including UHP WJ, Dry blasting, wet abrasive blasting, power tool cleaning, hand tool cleaning,
MCU-Miozinc
-
Surface tolerant MIO/Zinc filled primer
-
Better surface tolerance than epoxy mastic
-
Outperforms inorganic zinc primers
-
High DFT tolerance and unlimited re-coatable by itself
-
Compatible with most old coatings and different alloys
-
Full or spot primer on hand and power tool cleaned, (wet/dry) abrasive blasted or UHP cleaned surfaces
-
Versatile, easy to use, corrosion resistant primer
-
Does not require Sa 2.5 for maximum performance
-
Tolerates flash rusting
-
Recommend for immersion, splash zone and atmospheric exposure
MCU-Aluprime
-
High solids single component based on aluminium pigments primer
-
Most surface tolerance primer
-
Low viscosity, penetrating sealer to replace epoxy penetrating sealers
-
Outstanding abrasion & impact resistance
-
Can be used in combination with any type of surface preparation
-
Intermediate/Topcoat in highly abrasive environments
Intermediate & Functional Finishes
MCU-Ferroguard
-
MIO filled, refined coal tar MCU.
-
Outperforms coal tar epoxy in all uses.
-
Immerse within 30 minutes with or without the use of MCU-QuickCure in most conditions.
-
Available in black or red oxide colours.
-
Less irritating than conventional coal tar epoxy.
-
Two coat MCU-Ferroguard system passes 5,000 hours prohesion testing on steel
-
On any marine, offshore, hydro, wastewater or other structure exposed to salt or fresh water and sewage treatment.
-
Above or below grade service direct to concrete or steel.
-
Easily re-coatable and repairable.
MCU-Mastic
-
Universal intermediate/barrier coating
-
Coloured topcoat for interior use where there is limited UV exposure and slight ambering is acceptable
-
Aromatic topcoat to replace epoxy
-
High resistance to atmospheric chemicals
-
Best choice in salt or fresh water immersion service.
-
Ideal for use over MCU primers for long term performance in ballast tanks and cargo holds.
-
Free of tar
MCU-Miomastic
-
Used as an intermediate/barrier coating for new construction and full removal projects
-
High-solids aromatic intermediate for atmospheric service.
-
MCU-Miomastic contains a proprietary blend of Moisture Curing Polyurea resin and MIO and has many application and performance advantages compared to epoxy mastics.
-
On any marine, offshore, hydro, wastewater or other structure exposed to salt or fresh water and sewage treatment
-
Easily re-coatable and repairable
-
Ideal to use over MCU-Coatings´ primers for long term performance in atmospheric and interior service
Topcoats
High Heat
MCU-Insulat 230
-
For the 1st time, a 1 component moisture cure an insolation product can be applied on hot and cold temperature as well as high humidity such as coastal and marine & sweating pipes etc. This is not possible with existing tech products.
-
Be able to drastically reduce condensing of pipes and tanks
-
Increase safety by reducing temperature of hot pipes in close quarters.
Accelerators and Additives
CONTACT
"Join the MCU Revolution"
Inquiries
For any inquiries or questions
please call Johann on 021 955 501
or fill out the form below:
Head Office
Phone: +64 09 869 5150
Postal Address
B:Hive Building
Smales Farm
74 Taharoto Road
Takapuna
0622